Jump to content
The Classic Speaker Pages Discussion Forums

jamval

Members
  • Content Count

    6
  • Joined

  • Last visited

Community Reputation

0 Neutral

About jamval

  • Rank
    Newbie
  1. I have a set of Audax HD12x9D25 soft dome tweeters that are not working. I don't see any broken leads or anything that looks burnt, but they don't work, no continuity, test open. Here's what they look like: And taken apart: The existing coils/diaphragms are in a plastic holder. I will strip out the bad diaphragm salvaging the plastic holder: I can get new voice coil diaphragms like these: The question is how to make sure they are centered in the gap around the pole piece? Will this method work? First place shims around the OD and ID of the gap (I would use more shims, this photo is just for illustration): Next, after stripping out the old voice coil diaphragm, place the plastic voice coil holder on the magnet, there are two little posts that pressure fit into holes on the plastic holder where the red arrows are: Then place the new voice coil diaphragm into the gap, and glue it down to the plastic holder. Last, remove the assembled holder and new voice coil diaphragm, remove the shims. Attach/solder the lead wires to the terminal connectors. Put it all back together. Seems too simple, will this work? BTW this model tweeter does not have the ferrofluid. I have replaced a fair number of foam surrounds on cone drivers, but have never done one of these. Thanks for any advice.
  2. I'm not getting any response on the Bozak forum. It's really a question about an Audax tweeter, not made by Bozak. Hope it's not against the rules to post the details in this forum.
  3. Thanks for the reply. The first thread is more related to re-assembly after cleaning ferrofluid out of the gap and adding new fluid. Actually, that AR tweeter poses a bigger problem than mine to center the voice coil in the gap. The AR tweeter in the first post has the diaphragm voice coil attached directly to the top plate of the magnet. Where mine has a plastic holder that is self centering by means of little posts on the magnet plate. The only challenge for me is to get the new voice coil centered on the plastic holder. The second post seems more related to getting the top plate centered on the magnet after it had come off. In that one the poster made a cylindrical fixture to the correct diameter from a good tweeter. It doesn't show how he got the voice coil centered in the gap though. It does indicate to me, that I may be on the right track by using shims before gluing the new diaphragm down. The advantage I have is that once glued to the plastic holder, that holder can be popped off the magnet to remove the shims and make the final lead connections to the terminals. The replacement diaphragms are cheap, so I may just go ahead with my plan and document it. Thanks again for the reply.
  4. I have a set of DMS2500; B-800Bc woofers that are working, and what I believe are Audax soft dome tweeters that are not working. I don't see any broken leads or anything that looks burnt, but they don't work, no continuity, test open. Here's what they look like: Bottom: And taken apart: I can get new voice coil diaphragms like these: The question is how to make sure they are centered in the gap around the pole piece? Will this method work? First place shims around the OD and ID of the gap: Next, after stripping out the old voice coil diaphragm, place the plastic voice coil holder on the magnet, there are two little posts that pressure fit into holes on the plastic holder where the red arrows are: Then place the new voice coil diaphragms into the gap, and glue it down to the plastic holder. Last, remove the assembled holder and new voice coil diaphragm, remove the shims. Attach/solder the lead wires to the terminal connectors. Put it all back together. Seems too simple, will this work? BTW this model tweeter does not have the ferrofluid. I have replaced a fair number of foam surrounds on cone drivers, but have never done one of these. Thanks for any advice.
  5. OK, I will give it a shot. I thought about posting there, but since the tweeters aren't 'Bozak' I wasn't sure. And these DMS2500 are later model Bozak, post Rudy, and aren't considered 'classic' Bozaks. Thanks for the reply.
  6. I'm new here and an AK member suggested I ask for help here. But I'm not sure which forum to post to. I have a set of Bozak DMS 2500 2 way speakers. They have B-800Bc woofers and what I believe are Audax soft dome tweeters. The tweeters don't work, no continuity, test open. I want to replace just the voice coil/diaphragm and am looking for advice on how to make sure the voice coil is centered in the gap around the pole piece before gluing them. Is this the correct forum to be asking about this? If so I will post some photos and details of what I am attempting to do.
×