Jump to content
The Classic Speaker Pages Discussion Forums

Recommended Posts

Many of us "of a certain age" had our first real hi-fi experience as a result of building dynakits. They were well-designed and, in kit form, cheap enough for a student or newly-wed to afford. The instruction booklets were well-written and illustrated. Darn near fool-proof.

My first project was a Dynaco ST-35 tube amp that cost $45 including the tubes! A few years later I stepped up to the ST-120 and although some would argue the ST-35 was a "sweeter" little amp the 120 was pretty ground-breaking in its day. I eventually sold both (along with a PAT-4) but a couple of years ago I decided to get a used ST-120 to restore.

CSP member John O'Hanlon helped me find some replacements for the big capacitors but the amp had other issues so I put it aside until a couple of weeks ago. I was looking for mods and upgrades (the 40+ year old design does have shortcomings) when I stumbled across a gold mine!

http://www.updatemydynaco.com/ is a great site that offers a load of upgrades and improvements for the ST-120. Long story short: I ordered every possible upgrade (the "Full Monty"), leaving only the original chassis, power cord, binding posts and transformer. I opted to spend an extra $10 for the amp modules used the AkitikA GT-101 power amplifier. The difference between those and the regular ST-120 replacements: 0.1% versus 1% gain setting resistors, 10,000 uF output capacitors versus 3300 uF output capacitors. I also bought the new heat sinks (very nice but unnecessary), power supply upgrade, power supply and C12 caps and a blue LED mod for the power switch (purely cosmetic). The prices were very reasonable IMHO (total was under $200). I installed new RCA jacks and new feet that I had on hand but those are also available on the site.

Delivery was FAST. All of the parts are high quality and the new printed circuit boards are well-made and clearly labeled. Instructions (available on the site) are as clear and complete as the original Dynaco manual. Best of all: The owner/designer Dan Joffe provides super-fast helpful tech support (I had made one bone-headed goof).

So today I finished the amp and after bringing it up on a Variac (just a precaution) I gave it the real test: Powering the AR-3a's. The 3a's are supposedly power-hungry and at 4 ohms they pose a tricky load. I played a variety of music: Jazz, Rock, Classical (including organ) at decible levels WAY higher than normal. They sounded great. And the amp wasn't stressed at all. The heat sinks got barely tepid and there was no hint of clipping. According to Dan, the updated modules put out more than 50 Watts, but a shade less than 60 Watts into 8 Ohms and nearly 90 Watts into 4 Ohms. I plan to take the amp to my favorite tech for testing but to my ears it's all good. A few photos below of before & after, and the amp being auditioned.

IMHO the updatemydynaco kits are true heirs to the Dynaco legacy and Dan Joffe may be the latter day David Hafler. And the tech support is incredible.

If you have a tired old ST-120 do yourself a favor and update it with one or more of these modules. Don't have an ST-120? The AkitikA GT-101 provides the chassis and a modern torroidal transformer. Updatemydynaco also sells some modules and upgrades for the PAT-4 preamp, SCA-80 integrated amp and the mighty ST-400. Makes me sorry I sold my old PAT-4!

I have no connection with this outfit--just a really satisfied customer.

-Kent

post-101828-0-87664600-1402802967_thumb.

post-101828-0-10245200-1402802976_thumb.

post-101828-0-90355000-1402802984_thumb.

Share this post


Link to post
Share on other sites

Update:

Dan at Akitika (it's a palindrome) has just announced the release of his preamp kit. I have not built it but it looks like a winner. Sort of a 21st century PAT-4. It has a remote and expansion panels for future additions and improvements. Not much is made in the USA anymore, and the hi-fi components that are cost a fortune. This is a return to high quality affordable kit philosophy behind Dynaco and Hafler.

btw--I get nothing from this--I just think it's a worthy product and Dan is a good guy.

-Kent

check it out: http://www.akitika.com/.

post-101828-0-42917700-1426167191_thumb.

Share this post


Link to post
Share on other sites

A follow-up:

AkitikA's power amp kit, the GT101, has been replaced by the GT-102. Dan Joffe tells me the GT-102 is very similar to the "full monty" Dynaco ST-120 rebuild I did using his updatemydynaco kits.

Now Stereophile has reviewed the ST-102 in their July issue https://www.stereophile.com/content/hot-shade-july  Dan says "they loved it" but the review isn't online yet. 

If you are looking to breathe new life into your old Dynamo, this is a good resource: https://www.updatemydynaco.com

-Kent

Share this post


Link to post
Share on other sites

When I saw this thread pop up again, I had forgotten that I had read the original discussion and was expecting to see a different topic. These upgrade options for the Dynaco ST-120 are quite interesting (does that transformer get rotated?), and this is a really helpful write-up - - - thx, JKent. It is good to know that this amplifier has an option for an affordable upgrade for the DIY-er. Years ago, I had my own Dynaco system with ST-120, PAT-4, and FM-5, and it served me well for many years.

What I had expected was that this thread title would lead to a discussion of a new Dynaco amplifier introduced a little over a year ago. Since this falls within the scope of "Dynaco amp lovers!", I'll just add it to this thread - - I don't think this product has been mentioned yet in this forum. 

The product is a contemporary reincarnation of the venerable ST-70 tube amplifier, now called the ST-70 Series 3. Made in Canada but unavailable in kit form (and soon to be followed by a ST-1 preamplifier). The ST-70 appears to have a rugged build quality and the renewed aesthetics are very much in the spirit of the original. Selling for about $2K, it's still beyond my budget, but I somehow get the feeling it might just be all the amplifier I'd ever need. 

Website info: http://www.dynaco.com/st70#0

st70-slide-4.jpg

st70-slide-2.jpg

st70-slide-5.jpg

Share this post


Link to post
Share on other sites

That looks pretty cool! But I did a little searching and it looks like it's $3,000! Yikes!

It's amazing the staying power of the Dynamo line. I've seen a couple of modern-day renditions.

Here's an ST-70 kit: http://triodeelectronics.com/st70buildkit.html

Here are some more: https://www.dynakitparts.com/product-category/dynakit-products/amplifier-kits/

And some more: http://www.tubes4hifi.com/bob.htm#ST70

And Bob Latino is pretty well known http://bob01605.50webs.com

Of course, those are ll tube amps. updatemydynaco is the only outfit I know of that focuses on the solid state. Dan's kits are very nice and affordable. 

Share this post


Link to post
Share on other sites
4 hours ago, JKent said:

But I did a little searching and it looks like it's $3,000! Yikes!

Yikes indeed! I wish I could find the original preview article I read that was predicting the lesser price. Geez, it must be those recent trade tariffs kicking in already! :lol:  

Share this post


Link to post
Share on other sites

Here's the Stereophile review of the AkitikA GT-102 power amp:

https://www.stereophile.com/content/akitika-gt-102-power-amplifier

Here's the last sentence: "Super-highly recommended." Some people in the "comments" section say that Emotiva gives more bang for the buck. My original post was not about the complete amp kit per se but about my satisfaction with updatemydynaco.com. I love the instruction manuals, email support and all the clever updates for aging Dynamo gear. If you have an old Dynamo that needs updating, this is your source!

-Kent

Share this post


Link to post
Share on other sites

An update (no pun intended) on this: When I did my ST-120 I bought all the individual kits. Dan now has a complete upgrade kit and complete instructions, AND a YouTube video. Wish I had this when I did mine because IIRC I made one mistake.

Check it out: https://www.updatemydynaco.com/storeindex.html#OPA1611X2

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×